REMOTE CONTROL DUPLICATOR - INNOVATIVE ONE-TO-ONE KEY COPYING TECHNOLOGY

Description

It's always wise to have duplicate remotes available. So many times we tend to misplace these valuable remotes or lose them altogether. Then, we're either locked out of our garages or cars OR we have to pay big bucks to have them replaced. Ugh!

We've created this amazing remote duplicator that uses one-to-one technology for copying any wireless remote, car key, garage door opener, whatever! The password of each key is saved individually for your convenience. No worries! Our duplicator features high transfer sensitivity and no signal blocking. The device can attach right to your key ring and go with you anywhere.

NOTES:

• APPROACH TO DUPLICATING: Place the remotes side by side (as close as possible), then press the key of your old remote and the to-be-matched key remote simultaneously. The LED indicator will flash about three times, followed by a continuous fast blinking. Done!
• APPROACH TO CLEARING OLD CODES: Long press the upper two (A & B) buttons to clear old codes (The LED indicator will flash three times, followed by a continuous fast blinking, which is the sign of a cleared state).

PROGRAMMING:

Step 1 – Clear the Memory

1. Hold A and B buttons together - LED will flash 3x times
2. Keep holding down A button and release B button
3. Keep holding A button and push B button 3x times, LED will start flashing
4. Now press any key on the remote control, if LED lights are not bright, the code deletion is a success; if you press the button and the LED lamp is lit, the original code is not deleted!

Step 2 - Copy Your Remote Control

1. Put both remotes next to each other (touching). Make sure they have direct contact.
2. Hold 1 button on your original remote and 1 button on your clone remote.
3. Keep holding until the LED light blinks twice then blinks twice again then goes steady. This means the cloning has been successful.
4. If for some reason the clone does not go further than 2 blinks, it means the signal did not go through, please shift the remote slowly up and down until you get to the point where it will go through.

SPECIFICATIONS:

• Material: ABS + electronic components
• Compatible chips: 2262, 2260, 5026, 5326, 5326 - 3, 5326 - 4, FP527, PT2240, EV1527, HT6010, HT6014, HT12E, HT640, HT680, PLC168, SMC series, 9XX, PT2292, 12L - 4SC, HT6026, UM3750AM, etc.
• Compatible crystal frequency: 315MHz / 433MHz
• Powered by: 1 x 27A battery ( included )

New Quick Copy Remote Control Product Description

1, can copy the chip:

     2260 (all vendors), 2262 (all vendors), PT2264, 5326 (all vendors), SC5262, HT600, HT680, HT6207, HT6010, HT6012, HT6014, SMC918 series, 527 (all vendors), 1527 (all vendors), 2240 (all manufacturers), HCS101, HCS200\HCS201 (partial code), HCS300\HCS301 (partial code), some single-chip microcomputers..........

 

2, clearing method:

 Press and hold the "A" button and the "B" button at the same time, the LED indicator flashes three times, release any button that is pressed, the other one is not loose, click the button that is released three times, the LED indicator enters the fast flashing state. At this time, the data of the memory is completely cleared, and the remote controller after the data is cleared, no matter which button is pressed, the LED indicator is not lit.

 

3, the copy method:

    One hand holds the original remote control, the other holds the remote control, and the two remotes are as close as possible. (ideally, the two remotes are placed on the desktop with the zero distance on the side.) Press the desired button. The LED indicator flashes rapidly after three flashes, and the copy is successful. The other buttons operate in the same way. Some remote controllers have a small transmitting power, and they should be back-to-back operated with the original remote control and the remote control. Some operating environments have interference, and should avoid the interference operation. If the copying is not good, copy it again after clearing the code. (It's especially important: the remote control on your hand must work properly and be the same frequency as our remote control)

 

4, the new copy of the remote control features:

    Four buttons can be used to copy four different types of chips, that is, one remote can operate four different types of facilities. The frequency ranges from 270MHz to 434MHZ and more than ten frequency points. Copying data is faster, it is not easy to lose code, and the distance is far.

PACKAGE INCLUDES:

• 1 x Remote Control Duplicator